All Balls Racing Yamaha Viking Tie Rod Boot Kit (2004-2026)
Shipping calculated at checkout
In stock
The All Balls Racing tie rod boot kit for the Yamaha Viking, Wolverine and YXZ replaces worn factory parts to cure steering play, wander and torn boots. It is built to All Balls' application data as a direct replacement, so it goes back in where the original came out and restores tight, predictable steering and suspension.
Searching for yamaha viking tie rod boot, yamaha rhino tie rod boot or wolverine x4 tie rod boot? Use the exact-model fitment list below to confirm this kit matches your machine.
Kit contents per All Balls: boot x2, metal clamp x4.
Key Features
- Replacement steering rack (tie rod) boots sold as a left and right pair
- Metal clamps included to secure both boots
- Keeps water, mud and dust out of the inner tie rod and steering rack
- Low-cost fix that protects the rack from expensive internal wear
Built To Solve: Worn Yamaha Viking, Wolverine and YXZ Tie Rod Boot Kit Problems
- Torn or cracked rack boots letting in water, mud and dust
- Gritty, notchy steering from contamination at the inner tie rod
- Grease leaking from the steering rack joint
- A cheap boot failure turning into a steering rack replacement
Best For: Yamaha Viking, Wolverine and YXZ Owners Rebuilding Steering
- Yamaha Viking and Wolverine owners
- YXZ1000R and RMAX owners
- Yamaha Rhino owners
- Owners catching a torn boot before the rack is damaged
Specifications
- Brand: All Balls Racing
- Product type: tie rod boot kit
- Contents: Boot x2
- Contents: Metal clamp x4
- Covers: left and right sides
- Country of origin: China
- Manufacturer Part Number: 51-3001
Fitment
All Balls lists this tie rod boot kit for the following UTVs:
- Yamaha Rhino 450 (2006-2009)
- Yamaha Rhino 660 (2004-2007)
- Yamaha Rhino 700 (2008-2013)
- Yamaha Viking (2014-2026)
- Yamaha Viking VI (2015-2025)
- Yamaha Wolverine (2016-2018)
- Yamaha Wolverine RMAX2 1000 (2021-2026)
- Yamaha Wolverine RMAX4 1000 (2021-2026)
- Yamaha Wolverine X2 1000 (2024-2026)
- Yamaha Wolverine X2 850 (2019-2026)
- Yamaha Wolverine X4 850 (2018-2026)
- Yamaha YXZ1000R (2016-2025)
Fitment is based on the manufacturer's application data. Fitment is not guaranteed on unlisted models; confirm your exact year, model and package before ordering.
FAQ
What comes in the kit?
All Balls lists two boots and four metal clamps, enough for both sides.
Why replace a torn tie rod boot right away?
Once the boot tears, water and grit reach the inner tie rod and rack. Replacing a boot is far cheaper than replacing a steering rack or inner tie rods.
Which machines does it fit?
All Balls lists Yamaha Rhino 450, 660 and 700 (2004-2013), Viking and Viking VI (2014-2026), Wolverine 708, X2 and X4 (2016-2026), Wolverine RMAX2 and RMAX4 (2021-2026) and YXZ1000R (2016-2025).
Is this the inner rack boot or the outer tie rod end boot?
This kit is the steering rack (inner tie rod) boot set. Outer tie rod ends carry their own boots.
Is installation difficult?
The outer tie rod end usually comes off to slide the new boot on, so mark or measure the tie rod position first and check toe afterward. All Balls does not publish an install sheet.
Should I replace the tie rods at the same time?
If the inner joints are loose or the rod is bent, replace the tie rod assembly while the boot is off. If the steering is tight, boots and clamps alone are the right fix.
Why All Balls Racing
All Balls Racing specializes in replacement bearings, seals, steering and suspension rebuild parts for ATVs and UTVs, packaged by application so the right parts arrive for the job. Its kits are built as direct replacements for the factory parts they cover.
Protect Your Yamaha Steering Rack
Confirm your exact year and model in the fitment list, then inspect inner and outer tie rod joints while the boots are off. If a rod is bent or a joint is loose, add the matching tie rod assembly or outer end to the same order.
