All Balls Racing Ranger 500 & 700 Right Tie Rod Assembly (2005-2009)
Shipping calculated at checkout
Out of stock
The All Balls Racing right tie rod assembly for the Polaris Ranger 500 and 700 replaces worn factory parts to cure steering play, wander and torn boots. It is built to All Balls' application data as a direct replacement, so it goes back in where the original came out and restores tight, predictable steering and suspension.
Searching for Polaris Ranger 500 tie rods, Polaris Ranger 700 tie rods or 2007 Polaris Ranger 500 tie rod? Use the exact-model fitment list below to confirm this kit matches your machine.
Kit contents per All Balls: tie rod x1, tie rod end x1, boot x1, metal clamp x2, nut x1.
Key Features
- Complete one-side steering assembly: tie rod, outer tie rod end, boot and metal clamps in one kit
- Replaces a bent or worn tie rod without sourcing the rod, end and boot separately
- Boot and clamps seal the steering rack joint against water, mud and dust
- Built to All Balls' application data as a direct replacement for the factory parts it covers
Built To Solve: Worn Polaris Ranger 500 and 700 Right Tie Rod Assembly Problems
- A bent tie rod after a rock, stump or rut hit
- Steering play from a worn tie rod and end
- Torn boots letting dirt and water into the rack joint
- Toe that will not stay in alignment
Best For: Polaris Ranger 500 and 700 Owners Rebuilding Steering
- 2005-2009 Polaris Ranger 500 owners
- Ranger 700 and Crew 700 owners
- Ranger 6x6 700 owners
- Riders replacing a bent right tie rod
Specifications
- Brand: All Balls Racing
- Product type: right tie rod assembly
- Contents: Tie rod x1
- Contents: Tie rod end x1
- Contents: Boot x1
- Contents: Metal clamp x2
- Contents: Nut x1
- Position: right side
- Country of origin: Taiwan
- Manufacturer Part Number: 51-1040-R
Fitment
All Balls lists this right tie rod assembly for the following UTVs:
- Polaris Ranger 2x4 500 (2005-2009)
- Polaris Ranger 4x4 500 (2005-2007)
- Polaris Ranger 4x4 500 EFI (2006-2008)
- Polaris Ranger 4x4 700 (2005-2008)
- Polaris Ranger 4x4 700 Crew (2008-2009)
- Polaris Ranger 6x6 700 EFI (2006-2009)
Fitment is based on the manufacturer's application data. Fitment is not guaranteed on unlisted models; confirm your exact year, model and package before ordering.
FAQ
What comes in the kit?
All Balls lists one tie rod, one tie rod end, one boot, two metal clamps and one nut.
Which side does it fit?
All Balls lists this kit for the right side. The left side is sold separately (51-1040-L).
Which Polaris Ranger models does it fit?
All Balls lists the Polaris Ranger 2x4 and 4x4 500 (2005-2009), Ranger 500 EFI (2006-2008), Ranger 700 and Crew 700 (2005-2009) and Ranger 6x6 700 EFI (2006-2009).
What are signs of a bad tie rod?
A visibly bent rod, steering play, a clunk when turning and toe that drifts are the usual signs.
Do I need an alignment?
Yes. Set toe after installation. All Balls does not publish an install sheet.
Should I buy the full assembly or just the outer end?
If the rod is straight and only the end is worn, the outer tie rod end (51-1030) is enough. If the rod is bent or the boot is torn, the full assembly is the better fix.
Why All Balls Racing
All Balls Racing specializes in replacement bearings, seals, steering and suspension rebuild parts for ATVs and UTVs, packaged by application so the right parts arrive for the job. Its kits are built as direct replacements for the factory parts they cover.
Finish Your Polaris Ranger Right Side Steering Repair
Confirm the side and your exact year and model before ordering, and check the opposite tie rod, ball joints and boots while the front end is apart. Plan on a toe alignment after installation.
