Demon Arctic Cat Wildcat Rear Performance Axle (2014-2020)

Arctic Cat Wildcat owners run out of axle strength before they run out of nerve. This Demon performance axle is a direct-fit replacement for the rear position on the listed 2014-2020 Wildcat applications, built to hold up where the stock part gives in.

Rugged axles are packed with high quality moly grease for maximum lubrication and sealed with heavy duty neoprene boots and stainless steel clamps. Every Rugged axle is backed with a one-year manufacturer’s warranty. They are available across a wide range of ATV and UTV fitments, and they are the best price-point replacement going — the part that keeps you on the trail instead of on the trailer.

Key Features

• Direct-fit OE replacement geometry
• Chromoly steel shaft
• Molybdenum grease for low friction and smooth motion
• Boots designed to resist tearing and heat
• Built to restore stock performance without a dealer price

Built To Solve: Broken Rear Axles On A High-Power Sport Machine

• Rear shafts twisting or snapping on hard launches and hill climbs
• Driveline shudder that shows up under throttle and not on coast
• Torn boots throwing grease across the rear suspension
• Heat build-up in the rear CVs on long, fast desert runs
• Repeat rear axle replacement once tire size and power go up

Best For: Sport Riders Who Load The Driveline

• Dune and sand riders putting power down through soft ground
• Desert and whoop riders running long miles at speed
• Owners who have already broken an OEM shaft on this chassis
• Machines running a tune, a turbo or taller tires
• Anyone who carries a spare axle and would rather not need it

Specifications

• Position: Rear
• Sold as: Each
• Material: 4340 Chromoly Steel
• Warranty: 1 Year Warranty
• Shipping weight: 12.39 lb
• Manufacturer Part Number: PAXL-2019

Fitment

Demon lists this part for 2014–2020 Arctic Cat Wildcat Trail Rear Left, Rear Right Rugged Performance Axle.

Fitment is not guaranteed on applications outside that range. Confirm your model year, trim and machine width before ordering — and if you run aftermarket suspension, confirm your kit.

FAQ

Is this one axle or a pair?

One axle, sold each. Order quantity two if you are replacing both sides.

Why do stock axles break?

Axles fail where the shaft and CV joint run out of articulation and plunge travel under load. Demon uses larger CV joints and shafts and a dual heat treated chromoly shaft to raise that limit.

What are TPEE boots?

Thermoplastic polyester elastomer. Demon uses them because they are stiffer and more fatigue, puncture and temperature resistant than a standard OEM boot — boots are where many axle failures start.

How does this compare to the Heavy Duty version?

Demon's Rugged line is their OE replacement tier. The Heavy Duty line steps up to a dual heat treated chromoly shaft with a 4340 chromoly inner CV cage.

Does this fit my machine?

Check the fitment section above against your year, model and trim. Demon lists this part only for the applications shown, and fitment is not guaranteed outside them.

What warranty does Demon offer?

See the specifications above for the warranty Demon lists on this part.

Why Demon

Demon Powersports developed this line through years of research and development, aiming at parts that outlast the stock component without a race-parts price. Their products go through testing before launch, and the heavy duty and X-Treme tiers are what they put behind their own racers.

Complete Your Arctic Cat Wildcat Build

Confirm your year, model and trim against the fitment above before ordering, and check the position line — some Demon parts are sold each and some as a set. If you are replacing a worn part, look at what wears alongside it: on a driveline that means the carrier bearing and u-joints, on the front end it means ball joints and tie rods. Replacing one worn component next to another about to fail is how people end up doing the job twice.

Installation Video

Demon Powersports' official axle installation walkthrough: